Hot tapping in tanks according to API 653

Published 24 February, 2015 by admin

By Carlos Molina

According to API 653 3.14, Hot tapping identifies a procedure for installing a nozzle in the shell of a tank that is in service. This means that a tank can continue to be in operation whilst maintenance or modifications are being done to it. This is in complete compliance with the API 653 standard, but following some rules. First of all, for all of you students, let´s review what the BOK of the API 653 March 15 exam has to say.

HOT TAPPING
a) The Inspector should be familiar with the Hot Tapping requirements. (API-653, Paragraph 9.14)
b) The inspector should be able to calculate the minimum spacing between an existing nozzle and a new hot tap nozzle. (API-653 Paragraph 9.14.3)

[adToAppearHere]

Hot tapping is more common in pipelines, althought the principles are the same that for tanks. In a normal pipe hot tapping operation, you wish 2 or 3 things.

1. You want flow in the pipe so you can cool the welded zone, given that the liquid works as a heat sink.
2. You want no gases or vapors in the pipe
3. You want to weld nozzles and reinforcements to the pipe without penetrating too much in the base metal, because of pressure.

With tanks it is the same, with the diferrence that flow conditions in tanks are close to stagnant.

REQUIREMENTS FOR HOT TAPPING

The following diagram summarizes the requirements for hot tapping found in API 653 9.14

hot-taps-in-tanks

Requirements for hot-taps in tanks

1. Hot taps are not permitted on shell material requiring thermal stress relief
2. Welding shall be done with low hydrogen electrodes.
3. Hot taps are not permitted on the roof of a tank or within the gas/vapor space of the tank.
4. Hot taps shall not be installed on laminated or severely pitted shell plate. As an inspector, you have to make sure that thickness measures are taken in the proposed area for a hot tap.
5. Hot taps are not permitted on tanks where the heat of welding may cause environmental cracking (such as
caustic cracking or stress corrosion cracking).
6. Minimum spacing in any direction (toe-to-toe of welds) between the hot tap and adjacent nozzles shall be equivalent to the square root of RT where R is the tank shell radius, in inches, and T is the shell plate thickness, in inches.
7. Minimum distance between the toe of the hot tap weld and a vertical seam should be 12in

[adToAppearHere]
According to API RP 2201 (Remember this number very well as could be a question of the exam), the hazards for a hot tapping operation in tanks are the following:

a. Tank venting, with vapors reaching the exterior area where welding is taking place.
b. Product within the tank rising and overflowing.
c. Inadvertently allowing the liquid level within the tank to fall below the point of welding, exposing the vapor space within the tank to an ignition source.

Welding on the exterior of tanks in service shall not be conducted unless controls are established and in place to prevent flammable vapors from reaching the area of welding. Work must be stopped immediately should flammable vapors be detected in the welding area.

hot-tap-zones
When hot tapping or welding on a rank in service maintain liquid in the tank at a level at least 3 feet (1 meter) above the area where the work is being performed. No attempt should be made to hot tap or weld above this liquid level in atmospheric pressure petroleum storage tanks because of the potential danger of an explosive atmosphere inside the tank vapor space. Measurements of the tank level should be made by a hand tape gauge to verify the accuracy of automatic or remote reading gauges.

WELDING ON FLOATING ROOFS

Welding should never be allowed on the decks of floating roof tanks, as they are subject to flammability hazards in several locations:
a. Inside the pontoons.
b. Between the deck and liquid surface near the tank roof gauge float compartment
c. Near the roof seal vent.
d. Near the floating roof lift leg vent.
e. Between the primary and secondary seal.
f. Near the roof drain.

Thanks for reading this article and consider the following warning

hot-taps-warning

 

Latest comments

I have seen it done. Rememeber that API 650 and 653 go until the first face of the nozzle flange. So API 650 and 653 won´t answer you that. Thanks

- Carlos F. Molina

Is it possible to make a pipe connection to blind flange? Diesel oil tank spare nozzle : 8" (rating : #300) Pipe connection : 6" (rating : #300)

- Namgu.Kim

excellent information

- Ghanshyam Shukla

Hi. Table 9.1 is for deciding according to shell thickness. Obviously, there are many other things to take into account. It is the USER of the standard who must decide. Yes, the inspector can take that role.

- Carlos F. Molina

How to take decision to do Hot Tap in Tanks. By only Table 9.1 is sufficient? If the UT thickness reading are less than 0.5" can we assume this as recognize toughness Is Inspector involvement is must to decide Hot Tap feasibility?

- Soheb

How to take decision to do Hot Tap in Tanks. By only Table 9.1 is sufficient? If the UT thickness reading are less than 0.5" can we assume this as recognize toughness

- Soheb

Leave a Comment

Your email address will not be published. Required fields are marked *